Contact Us

No. 6, Tingkat Ciku 3,
Taman Ciku,
14000 Bukit Mertajam,
Penang,Malaysia

Tel : 604-530 3331, 604-530 0331
Fax : 604-5309331

Self-Clinching Fastener

 

MINIATURE FASTENERS
(Bulletin FE)
FLOATING FASTENERS
(Bulletin ALA)

Types : U, UL, FE, FEO, FEX, FEOX
General Information : Strong threads in a minimum of space. Available with locking or non-locking threads. Can be installed into sheets as thin as .020" / 0.76mm. Thread sizes #0 to 1/4" and M2 to M6.

Types : U, UL, FE, FEO, FEX, FEOX
General Information : Strong threads in a minimum of space. Available with locking or non-locking threads. Can be installed into sheets as thin as .020" / 0.76mm. Thread sizes #0 to 1/4" and M2 to M6.

SELF-CLINCHING FLUSH-HEAD STUDS
(Bulletin FH)
FLOATING SELF-LOCKING FASTENERS
(Bulletin ALA)
 Types : FH, FHS, FHA
General Information : Flush-head studs for sheet tichness of 0.040" / 1mm and greater.
 

Types : LAS, LAC
General Information : Floating action with locking threads compensates for mating hole misalignment. Thread sizes #4 to 1/4" and M3 to M6.

BROACHING TYPE STUDS
(Bulletin K)
BLIND FASTENERS
(Bulletin B)
 

Types : KFH
General Information : Studs for mounting into P.C. boards which can be used as solderable connectors as well as threaded fasteners. Thread #4 to #10 and M3 to M5.

 

Types : B, BS
General Information : Used for applications requiring closed thread ends. Blind end limits screw penetration and excludes foreign matter. Thread sizes #4 to 1/4" and M3 to M6.

BROACHING TYPE PANEL FASTENERS
(Bulletin K)
GENERAL-HEAD STUDS
(Bulletin CH)
 

Types : PFHK
General Information : Panel fasteners with spring-loaded captive screws mounting on P.C. boards. Thread sizes #4, #6 and M3.

 

Types : CHC, CHA, CFHC, CFHA
General Information : Installed into blind milled hole where surface opposite standoff must remain unmarred. Thread sizes #4 to #10 and M3 to M5.

FLARE-MOUNTED STANDOFFS
(Bulletin K)
CONCEALED-HEAD STANDOFFS
(Bulletin CH)
 

Types : KFB3
General Information : For spacing or stacking P.C. boards. Special for shanl is flared to increase push out resistance. Thread sizes #4, #6 and M3.


 

Types : CSS, CSOS
General Information : Installed into blind milled hole where surface opposite standoff must remain unmarred. Thread sizes #4 to #10 and M3 to M6.

FOILGARD FASTENERS
(Bulletin K)
PEMSERT FLUSH FASTENERS
(Bulletin F)
 

Types : KPS6
General Information : Used in plated thruholes in multi-layer P.C boards. The self-expanding shank ensures positive contact with plated thru holes. Thread sizes #4 to #6 and M3 to M5.

 

Types : F
General Information : Fasteners flush with both sides in sheets as thin as .060" / 1.5mm. Thread sizes #2 to 1/4" and M2 to M6.

GROUNDING STANDOFFS
(Bulletin K)
THIN SHEET SELF-CLINCHING NUTS
(Bulletin CL)
 

Types : SOAG, SOSG
General Information : Used to ground P.C. boards to steel or aluminium chassis. Annular projecting teeth eliminate the need for serrated or starwashers to make good electrical contact with the  circuit foil. Thread sizes #4, #6 and M3, M4.

 

Types : SMPS
General Information : These nuts feature a lower profile and can be mounted closer to the edge of a sheet than standard self-clinching nuts.

BROACHING SNAP-TOP STANDOFFS
(Bulletin K)
CONNECT'S WARE FASTENERS
(Bulletin CW)
 

Types : KSSB
General Information : All-metal standoffs with a spring action to hold a P.C. board securely without screws or other threaded hardware.

 

Types : DSO, DSOS
General Information : These self-clinching, screwlock standoffs are used primarily to mount D-sub connectors to panels.

TRI-DENT SELF-CLINCHING LOCKNUTS
(Bulletin CL)
CONNECT'S WARE FASTENERS
(Bulletin CW)
 

Types : SL
General Information : These locknuts are designed with a unique and economical TRI-DENT locking feature, which meets demanding locking performance requirements.

 

Types : CFN
General Information : These self-clinching, slare-mounted clinch nuts are for use in connectors such as D-subs, where a prevailing torque, non-metallic locking feature is required.

SELF-CLINCHING NON-FLUSH STUDS
(Bulletin FH)
CONNECT'S WARE FASTENERS
(Bulletin CW)
 

Types : TFH, TFHS
General Information : Non-flush studs for sheets as thin as .020" / 0.51mm. Stud head will projects above the sheet surface approcimentely .025"/0.64mm.

 

Types : SLPS
General Information : These self-clinch, slide latch, locking post fasteners are for use in D-sub cable assemblies that utilize Ethernet slide latch locking posts

SELF-CLINCHING HIGH-STRENGTH
(Bulletin FH)
SELF-CLINCHING NUTS
(Bulletin CL)
 

Types : HFH, HFHS, HFHB
General Information : For high-strength applications in sheets as thin as .50" / 1.3mm. Type HFHB is used for superior electrical / medichanical attachment in copper bus bars.

 Types : S, SS, H, HN, HNL, CLS, CLSS, CLA
General Information : Strong internal threads in sheets as thin as .030" / 0.8mm. Thread sizes #2 to 1/2" and M2 to M10.
LOW DISPLACEMENT HEAD STUDS
(Bulletin FH)
NUTS FOR STAINLESS STEEL SHEETS
(Bulletin CL)
 

Types : FHL, FHLS
General Information : Installs closer to the edge of a sheet than standard studs without causig that edge to bulge. Flushhead for sheets thichness .949" / 1mm and greater.

 

Types : SP
General Information : Installs into stainless steel sheets as thin as 0.30" / 0.8mm. Thread sizes #4 to 1/4" and M3 to M6.

STUDS FOR STAINLESS STEEL SHEETS
(Bulletin FH)
FLUSH-MOUNTED PILOT PINS
(Bulletin FH)
 

Types : FHL, FHLS
General Information : Install into stainless steel sheets as thin as .040" / 1mm. For use in sheet hardness of 92 or less on the Rockwell "B" scale.

 

Types : TPS
General Information : Self-clinching pilot pins satisfy a wide range of positioning, pivot, and alignment applications. The chamfered end makes mating hole location easy.

HIGH-STRENGTH STUDS FOR THIN SHEETS
(Bulletin FH)
  
 

Types : HFE
General Information : These self-clincing studs have an enlarged head diameter that provide high-strength in sheets as thin as .040" / 1mm.